No need for Porsche sport exhaust (pse) envy with this muffler! This offers weight savings and a far more exotic sound than the pse, all without drone. It is the perfect compromise for you and your loved ones. Rich, deep, turbo motorsport tones with the valves open and soft subtle, completely stock sounds with them closed. Top of the line or range depending on the english and is the best choice for a daily driver. Features: - + 16 crank hp & + 15 crank torque. - weighs 37 lbs. (17 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - direct bolt on replacement for the factory center muffler. - includes necessary installation hardware. - reduces turbo lag, backpressure and thermal lo...(choose a part on the right to read more)

Take your 991.1 or 991.2 turbo or turbo s to a new level with these muffler bypass pipes. They produce the wildest sound available on the market today and are a perfect upgrade for level 3 or 4 car used on the track. They produce loud, low, deep tones with exaggerated turbo whistling and sinister gurgling and crackling off throttle. By far the best sound you can get out of your turbo, not to mention being able to shoot flames! The only real drawback is the drone in the cabin which we try to minimalize by stepping down the diameter in 3 stages. Features: - + 35 crank hp & + 25 crank torque - 3 tubing (75mm) that tapers down to 2.25" (57mm) to prevent turbo damage. - weighs 7 lbs. (3,1 kg) - German v2a - x5crni1...(choose a part on the right to read more)

+ 15 hp & + 18 tq gain. - 2.5 tubing (63.5mm). - 4 x 4 (101mm) round tips. - 8.5 lb. Weight savings over OEM mufflers. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - electronic valve controller must be removed from the OEM unit and added to our muffler. - made in Germany. Please note: this muffler is a direct replacement the macan turbo (95b) model which comes with a single electronic exhaust valve on the passenger side. This is the very 1st aftermarket muffler for the macan 95b turbo that includes a valve like the factory system. This allows our system ...(choose a part on the right to read more)

The open architecture of this muffler allows for a deeper four-cylinder turbo tone, with plenty of whistling on tap. Coming off throttle from higher rpms exudes a chorus of snarling, gurgling and crackling letting everyone know that this car is not your average 982. + 15 hp & + 12 tq gain. - 2 x 3.5 (90 mm) round tips. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - lower deeper tones than the factory exhaust with far more whistling and gurgling / crackling off throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - no drone in the cabin. - "aero quip" style motorsport muffler connections t...(choose a part on the right to read more)

Are you one of those that are looking for more sound from your Porsche sport exhaust (pse)? Perhaps it's not quite as aggressive as you would like, or your last Porsche just sounded so much better? Don't worry, we have you covered, and the beauty is, you don't have to touch the catalytic converters which is a big no, no with Porsche dealers. With the valves open you receive a far more exotic, rich, deep, turbo motorsport tone and with the valves closed, soft subtle, completely stock sounds. So, absolutely no compromise and you will be thinking, the car really should have left the factory like this! Features: - + 10 crank hp & + 8 crank torque. - weighs 29 lbs. (13 kg) - German v2a - x5crni18-10 - 1.4301 stai...(choose a part on the right to read more)

The open architecture of this muffler allows for a deeper four-cylinder turbo tone, with plenty of whistling on tap. Coming off throttle from higher rpms exudes a chorus of snarling, gurgling and crackling letting everyone know that this car is not your average 982. + 15 hp & + 12 tq gain. - 2 x 3.5 (90 mm) round tips. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - lower deeper tones than the factory exhaust with far more whistling and gurgling / crackling off throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - no drone in the cabin. - "aero quip" style motorsport muffler connections t...(choose a part on the right to read more)

K-16/24 turbo (up to 555 hp) power is focused on low and mid-range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD Brombacher993 k-16/24 new turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The process starts with re-profiling the OEM turbocharger compressor housing and m...(choose a part on the right to read more)

K-16/24 turbo (up to 555hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbocharg...(choose a part on the right to read more)

This is for the 996 turbo model with logo in center tach. The differences are day and night! Gauge faces are one of the most visible and frequently looked at components in your Porsche. Why skimp on quality? Gauge faces should have clearly visible markings and be easy to read with and without back lighting. Replacement faces should offer similar qualities, but many gauge faces on the market don't quite make the grade. FVD gauge faces are different. What makes them different you ask? See for yourself. In the below pictures you will see that the tiptronic is an FVD gauge face and the 6 speed gauge face is the competitions. The daytime difference (the competition): darker, more yellow appearance raised orange war...(choose a part on the right to read more)

FVD Brombacher997.2 tt "700 series" upgraded turbos facts: - modified compressor housing for the 3.8 l displacement - modified & lightened billet compressor wheel with 12 blades - 49.55 mm inducer - 68 mm exducer - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already running FVD software we start by re-profiling the OEM vtg turbocharger compressor housing and modifying the compressor backing plate. This is done to replace the factory compressor wheel with a larger 12 blade, modified compressor wheel. The larger wheel is also lightened allows the turbo to flow a larger volume of air (more power), and aids i...(choose a part on the right to read more)

Purchase disclaimer: fabspeed motorsport does not condone the use of emission defeat devices for any vehicles used on public streets or roadways. Fabspeed motorsport will not tamper, remove, disable, or bypass emissions equipment on a motor vehicle in accordance with 40 cfr section 86.1854.12(a)(3), clean air act 40 cfr 1068.101(b). This includes software, known as tunes, that reprogram a motor vehicles electronic control module to alter engine performance and enable the removal of filters, catalysts, and other critical emissions controls.

The 2020 Porsche 911 Carrera is the next generation of Porsche flat-six twin turbocharged engines that have been further developed and are more powerful than ever before. ...(choose a part on the right to read more)

K-16/24 turbo (up to 555 hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbochar...(choose a part on the right to read more)

Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)

K-16/24 turbo (up to 555 hp) power is focused on low and mid-range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD Brombacher993 k-16/24 new turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The process starts with re-profiling the OEM turbocharger compressor housing and m...(choose a part on the right to read more)

Brombacher edition valved mufflers are the perfect compromise for you and your loved ones. Rich, deep race car tones with the exhaust valve open and soft subtle, nearly stock sounds with it closed. + 17 hp & + 13 tq gain. - 2 x 3.5 (90 mm) round tips. - includes a pierburg vacuum actuated exhaust valve. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - intoxicating growl at idle, partial throttle and wide open throttle with the valves open. Factory quiet with them closed! - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - "aero quip" style motorsport muffler connections to ensure a leak free exhau...(choose a part on the right to read more)

Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)

FVD Brombacher997.1 tt "700 series" upgraded turbos facts: - cnc re-profiled compressor housing and backing plate - new, lightened and larger compressor wheel (12 blades) - reworked turbine wheel, lightened and optimized for higher flow and reduced backpressure. - all new bearings. - all new piston rings and seals. - all parts cleaned, inspected and measured to motorsport specifications. - all parts are balanced (static & dynamic) up to 120.000 rpm with balancing protocol. - 47.55 mm inducer - 66 mm exducer - flow rate = 37 lbs. / minute or 280g/s - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already runn...(choose a part on the right to read more)

FVD Brombacher997.1 tt "700 series" upgraded turbos facts: - cnc re-profiled compressor housing and backing plate - new, lightened and larger compressor wheel (12 blades) - reworked turbine wheel, lightened and optimized for higher flow and reduced backpressure. - all new bearings. - all new piston rings and seals. - all parts cleaned, inspected and measured to motorsport specifications. - all parts are balanced (static & dynamic) up to 120.000 rpm with balancing protocol. - 47.55 mm inducer - 66 mm exducer - flow rate = 37 lbs. / minute or 280g/s - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already runn...(choose a part on the right to read more)

The moshammer evo 2 front chin spoiler blends a bit of Porsche heritage into its design with canard style winglets. This effective design transforms turbulent air into a more laminar flow, creating added downforce. Porsche active aerodynamics remains fully functional in all 3 positions and the evo 2 chin spoiler secures seamlessly into the factory locations. The evo 2 spoiler's design offers a more aggressive look but also blends perfectly with other design elements like the side skirts and rear spoiler. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of either the evo rs (991.2 turbo/s) or downforce rs...(choose a part on the right to read more)

FVD Brombacher997.2 tt "700 series" upgraded turbos facts: - modified compressor housing for the 3.8 l displacement - modified & lightened billet compressor wheel with 12 blades - 49.55 mm inducer - 68 mm exducer - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already running FVD software we start by re-profiling the OEM vtg turbocharger compressor housing and modifying the compressor backing plate. This is done to replace the factory compressor wheel with a larger 12 blade, modified compressor wheel. The larger wheel is also lightened allows the turbo to flow a larger volume of air (more power), and aids i...(choose a part on the right to read more)

The moshammer vented rear diffuser with fins is an aggressive design that reduces aerodynamic drag. This vented diffuser allows air that is trapped by the rear bumper to exit, allowing for greater top end performance. The design also incorporates 5 fins that improve laminar airflow by reducing turbulence. Moshammer manufactured this as a direct replacement, so it secures seamlessly to the factory locations with the original hardware. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of the downforce rs (991.1 turbo/s) package, the result is a confident, cohesive stance with balanced downforce. Features: ve...(choose a part on the right to read more)

FVD Brombacher997.2 tt "700 series" upgraded turbos facts: - modified compressor housing for the 3.8 l displacement - modified & lightened billet compressor wheel with 12 blades - 49.55 mm inducer - 68 mm exducer - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already running FVD software we start by re-profiling the OEM vtg turbocharger compressor housing and modifying the compressor backing plate. This is done to replace the factory compressor wheel with a larger 12 blade, modified compressor wheel. The larger wheel is also lightened allows the turbo to flow a larger volume of air (more power), and aids i...(choose a part on the right to read more)

The moshammer front fender set blends just the right amount of motorsport pedigree with functionality. This aggressive design is captivating on any 991 model and offers a level of exclusivity not found with competitors body kits. The integrated fender vents lower the thermal load on the brakes by allowing the heat to be quickly ventilated up and out of the wheel arch. This composite fender set has been meticulously designed to bolt up to the factory locations for perfect panel fitment, alignment and consistent gaps. A perfect addition for a leased vehicle or for those looking to return the car to its original appearance in the future. These fenders complement the entire moshammer stormforce (991.1) / stormforce...(choose a part on the right to read more)

The moshammer vented rear diffuser with fins is an aggressive design that reduces aerodynamic drag. This vented diffuser allows air that is trapped by the rear bumper to exit, allowing for greater top end performance. The design also incorporates 5 fins that improve laminar airflow by reducing turbulence. Moshammer manufactured this as a direct replacement, so it secures seamlessly to the factory locations with the original hardware. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of the evo rs (991.2 turbo/s) package, the result is a confident, cohesive stance with balanced downforce. Features: vented f...(choose a part on the right to read more)

FVD Brombacher997.2 tt "700 series" upgraded turbos facts: - modified compressor housing for the 3.8 l displacement - modified & lightened billet compressor wheel with 12 blades - 49.55 mm inducer - 68 mm exducer - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already running FVD software we start by re-profiling the OEM vtg turbocharger compressor housing and modifying the compressor backing plate. This is done to replace the factory compressor wheel with a larger 12 blade, modified compressor wheel. The larger wheel is also lightened allows the turbo to flow a larger volume of air (more power), and aids i...(choose a part on the right to read more)